- Get the taranis q x7 to work with heli x simulator upgrade#
- Get the taranis q x7 to work with heli x simulator software#
- Get the taranis q x7 to work with heli x simulator Pc#
- Get the taranis q x7 to work with heli x simulator simulator#
- Get the taranis q x7 to work with heli x simulator windows#
I HEAR (I have no first-hand knowledge to contribute yet) that smaller helicopters in sims, in general, don't have the same realism from a physics perspective as the larger ones do. Heli-X does exactly that, and I appreciate it. To me, Heli-X is a tool, and I expect my tools to do the job they were designed for, no questions asked. I would trade graphics quality for realism in a heartbeat. With that in mind, while I certainly appreciate the quality of the graphics, I chose Heli-X over others because of the physics (and training modes). I have 2 mCPX's and a T-Rex 450SE V2 (used off eBay of course) waiting to take to the sky, but until I get my orientation improved and comfortable with the cyclic controls, they're staying grounded (otherwise it'll be a prompt dirt nap for them, I have no doubt). I have yet to actually fly a collective pitch heli in real life. I would much prefer a wireless based connection Not a huge fan of it at all, but it works Never ran Heli-X on an HDD, but I think the SSD is the way to go Not exactly tearing up the frame rate, but get about 50-80 FPS
Get the taranis q x7 to work with heli x simulator upgrade#
Plan to upgrade to 16GB but I don't feel this hinders Heli-X (for my use) much Firstly, I just want to say overall that this sim is the best I have tried so far, and that's saying a lot since I've tried almost every one out there! So I just recently (today!) got Heli-X registered and downloaded the new version (7). In conclusion I just can't find any hardware solution for more than 4 channel functionality on Heli-X. Interesting to note: Heli-X does read the channels from SmartPropoPlus perfectly for a few seconds before the interference begins. Following this interference Heli-X detects nothing from the transmitter. Unfortunately as soon as I load Heli-X (within 10 seconds or so) I get a popup message from SmartPropoPlus that reads "Audio signal is OK but cannot calculate joystick position" and all functionality is lost. It's monitor shows them all reacting correctly to the inputs and it reads "fully operational". SmartPropoPlus does it's magic and detects 9 channels.
Get the taranis q x7 to work with heli x simulator Pc#
It even has been sticker labeled "MIX" and I don't think it can do any other function unless you physically alter the circuit on the board inside the controller.įinally I've been trying to use SmartPropoPlus with a simple mono audio cable connecting my Aurora 9X to the PC microphone jack. The right-hand toggle switch can't be used as Throttle Hold because it internally mixes the elevator and aileron channels in a weird 45 degree angle that I can't imagine how anybody would benefit from.
Get the taranis q x7 to work with heli x simulator simulator#
IMPORTANT - I wouldn't recommend this gutted transmitter to anyone for use as a 6 channel for helicopters with any simulator because the toggle switches will not function as required in any case. so again, no flight modes, no autos, besides using the keyboard of course.
Get the taranis q x7 to work with heli x simulator windows#
Windows joystick calibration detects it as 6 channels just fine but Heli-X6 only detects the sticks. I've bought the Hobbyking 6CH RC Flight Simulator System (Mode 2).
If anybody's looking for a cheap 4 channel interface that works I can recommend it. They don't put much details about it on the site and it ended up being a 4 channel so only stick control works. I've bought the Hobbyking USB Simulator Cable All in One. The seller just asked for it back and refunded me. I've bought a 6 channel USB interface cable from rcflieger96 on eBay and it wouldn't detect the aileron channel or any of the buttons so it was useless. After replacing it's built-in USB cable it worked again but had a lot of jitter and I had to calibrate it every time I wanted to use it.
I've been using an Esky gutted 4 channel controller that I bought from a local hobby shop and it worked fine until it suddenly died after about a year. I've been using Heli-X6 with the following:
Get the taranis q x7 to work with heli x simulator software#
It's a fun and high quality piece of software and I enjoy it a lot.
I run Heli-X on a semi-daily basis and it's helped me greatly in learning and practicing my skills.
0 kommentar(er)
